Handlebars

Budget-friendly mountain bars with stylish flair. - Plain gauge, tapered and shot-peened AL6061/T6 - Shot-peened for surface hardness - 15mm rise - 9° backsweep, 4° upsweep - Bar Clamp Diameter: 31.8mm - Material: Alloy - Width: 740mm

The WING/10a offers great fit versatility - allowing the rider to fine-tune the grip height for their riding style and comfort preferences. The straight hand grips are part of the flippable design that allows the grip height to be modified by 10mm. For optimal aero performance, the bar should be set in the low position to increase the separation from the armrests. Aero The Wing/10a employs a truncated airfoil (Kamm Tail) to stay within UCI regulations while offering the performance of a much deeper section. This, along with tidying up the underside of the wing where the cables used to exit has led to a small improvement in performance. For optimal aero performance the bar should be set in the low position to increase the separation from the armrests. Fit Data - The WING/10a is available in the following widths: 36, 38, 40, 42, 44 - The straight hand grips are part of the flippable design that allows the grip height to be modified by 10mm. The grip length can also be trimmed by up to 30mm. - The WING/10a offers the greatest fit versatility of any alloy basebar we’ve previously made, allowing the rider to fine tune for their riding style and comfort preferences. - An additional reason for the truncated design of the wing was to improve hand comfort when sitting up on the bar tops

Ergonomnic and elegant, the Whisky 438 Aluminum Scully Bar brings much needed relief for long hours in the saddle – without compromising reach or stem length. The 23-degree backsweep and 5-degree upsweep create an easy, natural handling position, leaving little room for tricep fatigue. The generous clamping space and clean, lightweight design means this ISO tested bar tastes all types of terrain. For a custom feel, the Scully Bar comes in two trimmable widths (820mm and 780mm) to perfect your grip length and enhance overall performance. 

TruVativ's tough Hussefelt Comp Riserbar is made from butted aluminum for a long fatigue life and great strength. The wide bar and high rise gives you an upright position for greater control in technical sections and confidence on steep descents.

- Double butted, tapered 6061 aluminum - Bead blasted anodized black

A25Y Alloy Riser Bar - Cut marks provide a range of width options - Textured Grit Grip finish in clamp areas eliminates over-tightening of components

The Service Course SL-80 provides comfortable and efficient positions on the bar tops, brake hoods, or down in the drops. The bar allows a neutral wrist position on the drops and a flat brake-hood transition. This minimizes the need for up-rotated bars. Drops are angled outward by 4 degrees, reducing wrist strain. Named after its 80mm reach to bring the hoods and control levers back where you want them. The ergonomic 125mm drop places the angled drop position where you can easily reach it while maintaining a neutral wrist angle. The SL-80's rounded bar top is clip-on compatible. Forged from lightweight 7075 aluminum. - Distinctive Zipp cosmetics - 7050 Aluminum - 80mm reach/125mm drop designed to fit a large number of riders - Clip-on compatible - Lifetime warranty

The Service Course SL-70 is the bike fitter's go-to bar. The short reach to the hoods allows a proper fit without compromising stem length and steering control. With the revised ramp angle, proper fit is now achievable on even the most challenging setups. The 70mm reach is the shortest of Zipp's Service Course bars. Together with its 128mm drop, the bar is deal for riders preferring a low body position. Whether it's a rider with a shorter torso or a bigger rider getting aero by pairing this bar with a long stem, this bar helps put just about any cyclists into their optimal position. - Distinctive Zipp cosmetics - 7050 aluminum for light weight and durability - 70mm reach and 128mm drop for a short-low position - Matte Black nano blast aluminum - Clip-on Compatible - Lifetime warranty

Upgrade your bike with FSA's Omega Road Handlebar. The double-butted, tapered and shot-peened aluminum construction makes this bar light and durable. It also features an ergonomic curve for comfort and a variety of hand positions. Plus, the Omega even sports a groove that makes cable routing easy.

Adventure handlebars from FSA are double butted, tapered, and shot-peened AL6061. - 31.8mm bar clamp diameter with 34 x 21 ergonomic oval section - 125mm drop, 80mm reach - 12° side flare

- Freeride inspired all mountain suitable geometry makes the bar extremely versatile - Rock solid in the park or on the trail - Cost effective upgrade to your cockpit without sacrificing quality - Shot-peening and anodizing enhances fatigue life even further - Material: Alloy - Weight (g): ±395 (25mm) / ±400 (40mm) / ±420 (60mm) - Diameter (mm): 31.8 - Rise (mm):25 / 40 / 60 - Length (mm): 785 - Geometry (Degree): 5°up x 8°back (25mm) / 5°up x 9°back (40mm) / 4°up x 10°back (60mm) - Finish: Shotpeen anodized, laser logos

- The original Chromag bar - Used from XC to DH, the OSX is Chromag's most versatile option - 31.8mm clamp Specs: - Rise: 25mm - Handlebar Width: 800mm - Stem Clamp Diameter: 31.8mm - Handlebar Material: Aluminum - Upsweep: 5 degrees - Backsweep: 8 degrees

A traditional looking 4-piece bar that uses larger radius bends, thicker walled, butted tubing and a traditional 7/8" crossbar for strength and durability. - Multi-Butted, traditional 7/8" crossbar for strength - Large radius bends for greater durability - Welded end caps to reduce flex - Post-weld heat-treated for added strength

The DRV/AEROa is a high-performance aluminum aero drop bar featuring a truncated airfoil for aerodynamics, comfort and stiffness. The curve has been optimized for modern road levers. The innovative fit and ergonomics of the DRV system include a 7° ramp angle and a 4° flare in the drops, allowing a natural wrist angle for enhanced comfort and control. The DRiVe metric by Profile Design pinpoints the precise position in the drops where riders instinctively place their hands. The metric is incorporated into a new series of progressively sized handlebars designed around a cyclist's most powerful hand positions. What is your DRiVe? Gone are the days of simply measuring a drop bar by the standard reach, drop and width. Our DRiVe metric pinpoints the precise position in the drops where riders instinctively place their hands. The metric is incorporated into a new series of progressively sized handlebars designed around a cyclist's most powerful hand positions. - The DRiVe Metric: The DRiVe (Drop Reach Variant) position is measured via a 73° line beginning at the bar bore. The DRiVe metric pinpoints the line intersection with the drop. - DRiVe Reclaims Comfort, Power & Control: Modern drop bar designs are deeply tied to tradition. They are designed based on outdated road bike sizing rendering many of cycling intended hand positions unattainable when riding modern frame geometry. The ride positions that are the most powerful and allow for the most control have now shifted into virtually unattainable positions. DRiVe reclaims many of the ideal positions most critical to comfort, power, and control. - Fit Made Simple: To predict the DRiVe position of any given rider, we looked at an anthropological study focusing on the correlation among handbreadth, shoulder width, and height. By measuring your handbreadth we can easily identify a DRiVe that will be compatible with your body type. - Progressive Ergonomics: The tops and hoods complement the powerhouse DRiVe position and the Reach and DRiVe are progressively sized as the bar increases in width. This progressive sizing ensures the most powerful positions remain right where they are needed. - Weight: 315g (38cm) - Size: 36, 38, 40, 42, 44cm (center to center) - Reach: 70, 75, 80mm - Clamp Width: 100mm - Clamp Diameter: 31.8mm - Clip Compatible: Yes - Drop: 122mm, 136mm, 148mm - Drop Outsweep: 4° - Drive: 105mm, 120mm, 135mm - Internal Cable Routing: Yes (Mechanical / Di2) - Max Brake Lever Torque: 10Nm - Max Torque Clamping to Bar: 6Nm - Material: 6061-T6 AL

- The FatBar Carbon is the ultimate DH race handlebar. - This ride-tuned handlebar combines the ultimate blend of strength, stiffness and shock absorption.

We threw in a bit of everything for our take on the ultimate gravel handlebar setup. Rise, sweep, and flare make for an ultra-comfortable handlebar that keeps you in control no matter the terrain. Add the Cruise Control Top and Drop Grips and our Really Long Bar Tape to get to next-level comfort and performance. For the rider that wants to go everywhere, the Kitchen Sink Handlebar is the bar that has everything. With widths from 44 cm up to 50 cm, it's clear we believe in wide. But the added stability and control of a wider bar should not come at the cost of comfort. So we've thrown everything into this handlebar: - 20mm RISE means less pressure on the hands and a broad range of fit options. - 7° SWEEP means the bar is positioned where your hands want to be, whether you're on the flats, the hoods or the drops. - 25° FLARE on a compact drop means a stable, aerodynamic drop position that is actually comfortable enough to use. - Optional endurance loop adds an alternative aerodynamic riding position and a perfect spot for gear storage and mounting accessories.

Easton’s new AX series now includes our budget friendly EA50 AX flared drop bar. With the same MCD drop technology as our top of the line road bars, flared to 16 degrees for comfort in the drops and control on gnarly terrain or long gravel assaults. It's time to take the road less traveled with EA50 AX. - Finish: Black Ano/Water Transfer Graphics - Bar weight: 325g (42cm) - Clamp diameter: 31.8mm - Width (center-to-center): 40cm, 42cm, 44cm, 46cm - Flare: 16-degrees - Reach: 80mm - Drop: 120mm - Materials: EA50 alloy

You say you want a wide, stiff, strong, championship-winning design? Here you go. The new Descendant DH bar borrows from a rich championship-winning heritage, and adapts it to today’s aggressive courses and riders. Descendant DH bars are the command center of cornering control. - Stiff, precise, and super-wide - Made with tough 7050 alloy - Descendent geometry from TruVativ's best enduro rider’s input - Backsweep: 9° - Upsweep: 5°

Get back on the road with a replacement handlebar for your bike. Customize your bike with a new handlebar that fits your own personal style. PRODUCT DETAILS - Original equipment replacement for bikes with 31.8mm stems - 6062 alloy with a matte finish

Truvativ design built in collaboration with, and featuring the creativity of, Troy Lee Designs. The Truvativ CoLab TLD bar is the command center of cornering with an artistic flair. - Includes Rockshox sticker pack to give fork and handlebar a unified custom look - Stiff, precise and wide - Signature Troy Lee Designs style - Geometry and 7050 aluminum are designed for DH and gravity events - Back Sweep (deg): 9 - Upsweep: 5 - Weight: 349g - Material: Aluminum

For the ultimate in comfort and control over long distances, our all-carbon Scully Bar pairs a 5-degree upsweep with a 23-degree backsweep. Featuring an elegant forward bend before sweeping back again, its easy, natural hand position inspires confidence. It’s also blissfully wide, offering loads of real estate up top for mounting lights, bags, bikepacking gear, and more. ISO tested for harsh terrain, the Scully Bar is a sleek and stiff upgrade for paved commutes and whatever off-road riding you’re into — gravel, XC, singletrack, and beyond. Offered with 20mm of rise in two trimmable widths, the ideal fit is out there.

Combine a proven shape, proven width, proven materials and a take-no-prisoners approach, and you’ve got the new Carbon 7050 Descendant riser bars. They are stiff, tough, dependable, and give you all the comfort and positive steering feel you could want. Descendant series bars are the new normal for comfort and control. - Material: Al-7050 - Width: 760mm - Backsweep: 7-degrees - Rise: 20mm - Upsweep: 5-degrees - Colors: Black

Race Face Atlas riser handlebar with an anodized, shot-peened finish. - Anodized, shot-peened finish - Cold-drawn and butted proprietary AirAlloy aluminum tubing - 4 degree upsweep

- Perfect townie bike bar or think of it as an inverted moustache bar - Rigid aluminum construction, compatible with MTB-style levers

Get back on the road with a replacement handlebar for your cruiser bike. Customize your bike with a new handlebar that fits your own personal style. PRODUCT DETAILS - Traditional 35 degree back sweep handlebar - 6061-T6 polished aluminum with anodize finish - RIDE+ versions have an integrated cable guide inside

Velo Orange's Milan bar is so named because it's a great bar for converting an old Italian racing frame with a short top tube. Actually, it's great for converting any frame with a short top tube into a city bike. Folks who like a more aggressive position on a city bike will like it, too. The width is about 570mm and reach is 110mm; there is around 25mm (approximately one inch) of rise. The grips sweep back about 35 degrees, and the grip area is about 170mm long. The clamp area is 25.4mm. The material is polished aluminum alloy. Milan bars work with regular MTB (22.2mm) grips, brakes, shifters, 22.2 inverse brake levers, etc., but not bar-ends.

You say you want a wide, stiff, strong, championship-winning design? Here you go. The new Descendant DH bar borrows from a rich championship-winning heritage, and adapts it to today’s aggressive courses and riders. Descendant DH bars are the command center of cornering control. - Material: Al-7050 - Width: 800mm - Backsweep: 9-degrees - Rise: 25mm - Upsweep: 5-degrees - Colors: Black

With multiple geometry options to choose from, Wald's Steel Handlebars offer great options for riders looking to accessorize their bike or find a replacement option that feels comfortable. - Chrome finish - Made in the USA - Weight: 726g - Lever Compatibility: Mountain 22.2mm

Simply put, it's the perfect trail bar. The M6 bar is tuned for the dream combination of response, compliance, and high strength. Available in a traditional 25mm rise or a low 7.5mm rise, it sweeps back at 9 degrees and up 5 degrees, providing excellent support and a classic fit. Designed around a 31.8mm clamping diameter, the carbon laminate is tuned to deliver the ideal flex profile for trail use. This bar provides excellent vibration damping and response, making it the perfect choice for long days on epic terrain. - Material: Carbon Fiber - Weight: 200g (25mm rise); 190g (7mm rise) - Bar Width (Max): 780mm - Bar Width (Min): 740mm - Clamp Diameter: 31.8mm - Sweep: 9 Degrees - Tip: 5 Degrees - Torque Spec: Face Plate: 5.5Nm - Torque Spec: Controls: 5.5Nm

The Surly Corner Bar is for off-road riders who want to give drop bars a try without swapping out the drivetrain and brake levers on their current mountain setup. Does that make it an economical option for fresh excitement on the trail? Yes, it does. - Chromoly steel with custom-butted tubing - 22.2mm grip diameter - 25.4mm clamp diameter - One set of 25.4/31.8 x 60mm Problem Solvers shims included